How to connect DVR via internet to watch CCTV cameras from a remote place

[polaret]

Hello
I have a DVR and i want to connect it to the internet to wach my store from far away (my home).
i have static ip and i am a litle confused what IP should i type to connect to the internet ---my static IP ---the DVR IP---the dns IP ----the router IP

Setting up DVR to be used from remote location:

1. Connect your DVR to your router
2. Use menu on DVR to assign internal IP and gateway and port number.
   
   This Local IP must be in the same Gateway range as the Router. If you are unsure check the Router and locate the Status section, or goto the Command prompt of Windows XP and type in ipconfig.
   
   Look for Gateway. If the Gateway is 192.168.1.1, then you can make the DVR's IP anything from 192.168.1.2 - 192.168.1.255.
   
   Also you will need to use the same SubNet Mask, which is typically 255.255.255.0, and also use the same gateway.
3. Next find out what port your DVR uses. The easiest way to it is by reading the manual of your DVR. Look for the network section of it.
   
   Also if it comes with network software, check out if in the connection area the software shows the port number.
   
   Also check the Server software/Programming (Network section of it) to see if the port is listed.
   
   In many cases it will be as simple as just Port 80, which is an HTTP port.
4. Set your router to forward chosen port to internal IP address of DVR.
   
   To access the Router itself, use the Gateway you just located. If the gateway is 192.168.1.1, then enter that into the location edit box of your browser and then click the Enter button. A username and a password are typically required, but it depends on a router. For Linksys use "admin", "admin". By default DLink doesn't require any username or password (It is highly recommended to change the default password).
   
   Once you're logged into the Router, in the Applications & Gaming Section / Servers of the Router, you need to add a Server/Application. Enter the port number and select TCP only. Where it says Port 0 to 0 enter the same port number twice. Or if your DVR uses for example, ports 3550, 4550, 5550, 6550, and there is nothing else utilizing these ports in between, then you can actually just enter one line, 3550 - 6550.
   
   Enter the DVR/Cameras internal IP.
   
   Enable it.
   

   Originally Posted by Example

   If the port was 1024, and the Local IP is 192.168.1.200, then it would be:
   
   NAME = Anything you want
   Port = 1024 TO 1024
   TCP/UDP = TCP
   LOCAL IP = 192.168.1.200
   ENABLED = CHECKED
   
   OR
   
   NAME = Anything you want
   Port = 3550 TO 6550
   TCP/UDP = TCP
   LOCAL IP = 192.168.1.200
   ENABLED = CHECKED

5. Set up additional entries for as many ports the DVR uses, to the same local IP. Check your DVR manual and it's networking section for all additional ports required. Also check the DVR software itself.
   
   If your router has enough free entries, you can seperate them. Use it like DVR_HTTP for the browser port, DVR_AUDIO for the audio port, etc.
   
   If you are going to use VNC to a PC DVR, then you would need to set up port 5900, and perhaps call it VNC_DVR, for example.
6. You have a static IP so you don't need to use a Dynamic DNS sevice . You just enter your static IP and your router forwards packets to your DVR.

Source: How to set up DVR to watch CCTV security cameras over Internet (Tutorial)

[polaret]

The DVR has default IP and port 80 do i have to change that you mean no i think

# Set router to forward chosen port to internal IP address of DVR. For example: route port 80 to 192.168.1.10.
# You have a static IP so you don't need to use sevices like www.dyndns.org

How can i set the router to do that
And for educational reason i have create a hostname in dyndns.org how can i set it up

[polaret]

Sorry i forget to write i have a speedtouch

Originally Posted by polaret

sir i want to know that where we have to use static ip

if it is possible pls send all command and how can i install dvr on a internet.and what shoul we do for this

Every router is different. There are no any general instructions on how to set up all of them. Manufactures always provide manuals so you should refer to them.

Using dyndns.org with your DVR

• Create an account with a username and password.
• Login
• "Account" -> "My Service" -> "Add Host Services" -> "Add Dynamic DNS Host"
• Enter and select hostname
• Enter IP address of your computer
• Click "Add host"
  In your DVR software:
  • Find DDNS network settings
  • Enable DDNS
  • Enter username, password and hostname from dyndns.org
  • Apply the settings

Then if your IP address changes, DVR software sends the data to dydns.org and updates it. This allows to access your computer from remote location by using not a weird IP address, but a user-friendly hostname.

p.s.Please note that routers can also be configures to work with DDNS (instead of configuring DVR software, you can configure your router).

I am trying to connect through ADSL router. but i got the message "failed".
in DVR, should i use DHCP, static ip or whatelse?
what IP should I assign for DNS host?
in ADSL router, again, what is the IP that should be assigned to DDNS?
Please Please Please reply

yagoms0a, If you don't have static, you need to set up a DDNS. Have you set up your DVR to work with DDNS as described above?

Have you set up your router to forward data to a DVR as mentioned above?

yagoms0a, If you don't have static, you need to set up a DDNS. Have you set up your DVR to work with DDNS as described above?

Have you set up your router to forward data to a DVR as mentioned above?

[digicell]

Originally Posted by Stream Recorder

Every router is different. There are no any general instructions on how to set up all of them. Manufactures always provide manuals so you should refer to them.

Using dyndns.org with your DVR

• Create an account with a username and password.
• Login
• "Account" -> "My Service" -> "Add Host Services" -> "Add Dynamic DNS Host"
• Enter and select hostname
• Enter IP address of your computer
• Click "Add host"
  In your DVR software:
  • Find DDNS network settings
  • Enable DDNS
  • Enter username, password and hostname from dyndns.org
  • Apply the settings

Then if your IP address changes, DVR software sends the data to dydns.org and updates it. This allows to access your computer from remote location by using not a weird IP address, but a user-friendly hostname.

p.s.Please note that routers can also be configures to work with DDNS (instead of configuring DVR software, you can configure your router).

Hi

I am trying to set up my camera so i can see it from external location. I have a dynamic IP so i created the DynDNS account and went through that configuration......I have a LJD Deltaware Camera and it came with an application I can install to view the cameras. I want to know if I can use this on a WEB INTERFACE because I want to view it online from anywhere instead of having to install this software all the time?

When i try to go to my HostName it comes up with error so is there somehting I need to do to see it on IE7 or Firefox etc rather then using that application?

I have the 8 channel Dedicated DVR - http://www.adata.co.uk/default.asp?t...28Deltawave%29


Thanks

Pranav